Jokers Racing > Yamaha YFZ450 Parts > YFZ450 A Arms & Swingarms

Yamaha YFZ450 4130 Chromoly Racing Swingarm (American Star)

ASR Oval Tube Chromoly Racing Swing-Arms are without a doubt the very best built, very best looking Swing-Arms in the industry today. Super strong, they are manufactured out of Oval Tube 4130 Aircraft Grade Chromoly Steel. Notice 4 Bolt Pinch Tubes at the rear. Additionally they are available with or without the Rear Billet Aluminum Bearing Carrier.

Yamaha YFZ450 Bearing and Seal Rebuild Kit (Hardkor)

Each kit includes all bearings, seals and dust cap O-rings to restore your hubs to new condition. Fits all Honda and Cannondale Models, Yamaha Raptor and YFZ450 (standard and 144mm bolt pattern)

Yamaha YFZ450 A Arm Bearing Bronze Bushing (ModQuad)

Bearing Bronze A-Arm Bushings Set. Choose the 6 pc. or the 12 pc. set Fits Banhsee, Raptor, YFZ 450 & Blaster ATV's. 6 Piece
12 Piece

Yamaha YFZ450 A Arm Black Delrin Bushing Set (ModQuad)

A-Arm Black Delrin Bushing Set. Fits Banhsee, Raptor, YFZ 450 & Blaster ATV's. Choose a 6 pc or 12 pc set. 6 Piece
12 Piece

Yamaha YFZ450 Axles (Durablue)

Eliminator Axle: For high performance & race applications! Eliminator is the worlds #1 axle. It features a proprietary heat treating process that provides excellent wear and strength characteristics. It is then polished and chrome plated, giving you a product that is superior in strength as well as good looks. Many of the models come with the patented PosiâLock system which removes threaded sections from the flexing area of the shaft (a source of crack generation). Use this axle for all forms of racing and high performance applications. It comes with a Warranty to Original Purchaser against bending or breaking. *Stronger* *Widens Track* *Increases Stability* *Excellent Reliability* *Warranty to Original Purchaser on Eliminator Axles*

1. Remove the old axle, noting the position of the disc and sprocket flanges. 2. Remove the Posi*Lock nut assembly from the Durablue axle by removing the c-clip ring and sliding off the nut assembly. The nut assembly will be reinstalled the same way, so pay attention to the Posi*Lock orientation on the axle. 3. If you are installing the axle in a pre 2003 Blaster, remove the c-clip and keeper ring from the brake side of the axle (the larger of the two inner-most splines). Take the large ring from the plastic sack and slide it onto the axle so that it is between the carrier bearing and the larger diameter spline. When installed correctly, this ring covers a section of spline. Skip to #5. 4. Slide the brake hub (Banshee) or sprocket hub (Raptor) onto the axle. 5. Slide the axle through the bearing carrier. 6. Slide the sprocket hub (Banshee/Blaster) or brake hub (Raptor) onto the axle. 7. Install the nut assembly as shown. Tighten the axle in the bearing carrier 20-40 lbs-ft (not especially important, just tight). Tighten the allen screw to 17 lbs-ft, clamping the nut. 8. Pre 2003 Blaster owners will need to slide the brake rotor flange onto the axle the flange "floats" on the spline). Ride the vehicle and check for axle tightness. 9. (You may have to retighten the axle. After retightening, use a thread lock compound on the s screw when clamping for the final time.

Yamaha YFZ450 Anti Vibe Steering Stem (Janssen Motorsports)
Janssen Motorsports stems are constructed out of high strength 4150 chromoly steel. All stems are gusseted and fully TIG welded in all vital stress areas. All stems will include a 6061-T6 billet aluminum vibration/dampening handlebar clamp. These clamps can be ordered to handle either standard 7/8 inch bars or 1 1/8 inch fat bars. All stems come in triple plated show chrome to maintain an outstanding appearance and insure smooth operation. Janssen Motorsports stems have a standard +1 inch rise over stock but can be ordered in any length and either a +0 or +1 forward offset.

Yamaha YFZ450 Maximum Ground Clearance SLICAST A Arms (Houser Racing)
â Maximum Ground Clearance â 11.5" of wheel travel â Uses 18.5" length shocks â 4130 Chromoly steel â TIG welded construction â Replaceable HOUSER press in bottom ball joint â Adjustable camber & caster using SLICASTâ method â Lightweight Chromoly tie rods, chrome plated â Uses needle bearings â Threaded grease zerks â Chrome dust covers with seals â Hardened thrust washers â HOUSER logo powder coated onto A-Arms ** NOTE: SLICASTâ is a Patent Pending product +.5â Wide, +0â Forward $950 Gloss Blue $950 Transparent Red $950 Gloss Black +2â Wide, +0â Forward $900 Gloss Blue $900 Transparent Red $900 Gloss Black +2.5â Wide, +0â Forward $900 Gloss Black RED represents the normal clearance A-Arms as the BLACK is the additional clearance A-Arm

Yamaha YFZ450 Bearing Carrier (HOUSER RACING)
Bearing Carrier,2003-2005 Yamaha YFZ450 RHBC Swing Arm. Note: Can only be used on Houser Racing 2003-05 YFZ450 Round Housing swing arm.